
How a Slate Roof Is Installed in Sydney: The Steps From Inspection to Ridge Capping, Explained by Slate Roof Restorations
A slate roof installation in Sydney follows a set order. The roof is inspected, the slate is chosen, the old roof is stripped by hand, the timber frame is checked and repaired, new sarking and battens go down, and each slate is measured, cut where needed and fixed by hand. The flashings, valleys, ridge capping and leadwork are fitted last.
Slate Roof Restorations installs new slate roofs on heritage and established homes across Sydney, and our own team carries out every stage from the first inspection to the final check. This guide walks through each step of a slate roof installation so you know what will happen on your roof and why each step matters.

When Does a Sydney Home Need a New Slate Roof Installed?
A new slate roof is usually installed when the parts under the slate have worn out. The signs we look for during an inspection are failing battens, widespread nail sickness, failed underlay, damage to more than half of the slates, or structural concerns with the roof frame itself. When any one of these signs is present, a full reroof is a better long-term decision than a series of repeated repairs.
The St Leonards home in our Lower North Shore slate roof project had a slate roof more than 100 years old, and its slates, ridges and valleys had reached the end of their life. If your roof still has years left in it, a repair is the better choice, and our slate roof repairs page explains what that involves.
What Happens During a Slate Roof Installation in Sydney?
Every slate roof installation we carry out follows the same sequence, and we don’t move on to the next step until the last one is done properly. Here is what happens at each stage.
Inspecting the Slate, Timber and Flashings
A slate roof installation starts with a thorough inspection of the slate, the timber, the underlay, the flashings and the ridgeline. After the inspection, we walk you through what the roof needs and why. This is also when we confirm whether a full installation is needed at all, or whether the roof can be kept going with repairs or a restoration.
Choosing the Slate for Your New Roof
The next step is choosing the material that suits the house. We install new slate from the Welsh Penrhyn, Canadian Glendyne and Spanish Cafersa quarries, and we use reclaimed slate when it is the better way to match an existing roof. Where a house calls for it, we also work with terracotta tiles and shingles. We source all of the roofing material ourselves.
Stripping the Old Slate Roof by Hand
We strip the existing roof by hand. Any slates that can be saved are sorted and set aside for reuse. On some homes we take the roof back to the rafters, as we did on the St Leonards home, so the new roof can be built up from a clean start while keeping the period style of the house.
Repairing the Timber Frame and Laying New Sarking and Battens
Once the old roof is off, we inspect the timber frame and repair it wherever it needs it. New sarking and new battens then go down. The sarking adds weather protection under the slate, and the battens give the slates a solid, even base to sit on.
Measuring, Cutting and Fixing Each Slate by Hand
With the base in place, the slates are installed. Each slate is measured, cut where it needs to be and fixed by hand using traditional methods rather than shortcuts. We lay every slate with the same care and patience the original roof would have been built with.
Finishing the Flashings, Valleys and Ridge Capping
The last stage of a slate roof installation is the detail work. We fit new flashings, valleys and ridge capping, along with any lead or metal work the roof needs. Lead flashing protects the vulnerable joins around chimneys, valleys and skylights, and without good flashing even well-laid slate will eventually fail. Our leadwork and metal roofing page covers this work in more detail. We check every detail before the roof is signed off.
Which Materials Go Into a New Slate Roof Installation?
The slate is the part everyone sees, but a new slate roof relies on the materials underneath it as well. On the Manly slate roof replacement, the original battens, sarking and fixings had deteriorated, which is not always visible from the street.
For the Manly roof, we used the following materials:
- Canadian Glendyne slate for the roof itself
- Permo Air HT sarking for weather protection
- European pine battens installed to current industry standards
- Copper nail fixings for corrosion resistance
- Traditional terracotta ridge caps to keep the home’s original character
- Custom leadwork and Colorbond valleys in Woodland Grey
A slate roof installation is also a good time to look at the rest of the roof system. On the Manly home we added new valleys, upgraded the gutter brackets, fitted leaf guards, replaced the box gutters and capped the chimney pot. Each of these upgrades helps the roof handle the heavy rain and storms that are common on the Northern Beaches.

How a Slate Roof Installation Is Run on a Home You Are Living In
Both homes in our St Leonards and Manly slate roof projects stayed occupied while the new roof went on, so we plan the work around the people living there. The Manly slate roof installation took about six weeks, and that time covered scaffolding, safety compliance, demolition, installation and finishing. We staged each part of the roof work to keep noise, dust and disruption down.
Slate Roof Installation on Heritage Homes in Sydney
Federation and Victorian era homes are common across Sydney’s Eastern Suburbs, Lower North Shore, Inner West and Northern Beaches, and our team understands what a new roof on these homes needs to look right and perform for the long term. If your home is heritage listed or sits in a heritage conservation area, you may need council approval before a new slate roof is installed. The work then has to follow heritage guidelines on materials, colour and the method of installation.
We can work with reclaimed slate or source new slate that closely matches the colour, texture and size of the original, and details such as terracotta ridge caps help a new roof keep the look of the house. Our guide to slate roofs and heritage requirements in Sydney explains how to check whether your home is listed and what approvals involve.
Why Choose a Slate Roof Installer Whose Own Team Does the Work
When you book a slate roof installation with Slate Roof Restorations, you deal directly with the people who inspect the roof, install it and stand behind it once it is finished. You won’t be passed to a call centre or a rotating crew of subcontractors. Every reroof comes with a written guarantee.
Our team has more than 30 years of hands-on experience with slate, terracotta and heritage roofing, and we hold Contractor Licence 459374C. You can read more about the full process on our Sydney reroofing page.
Frequently Asked Questions About Slate Roof Installation
Who installs the slate on a Slate Roof Restorations roof?
Our own team installs every slate roof, from the first inspection through to the final check. You speak directly with the people who inspect the roof and do the installation, rather than a call centre or a crew of subcontractors.
Why are copper nails used when installing a slate roof?
Copper nails resist corrosion, which matters on a roof that can last well over 100 years. On the Manly slate roof installation, we fixed the Canadian Glendyne slate with copper nails for that reason.
Do I need council approval to install a new slate roof on a heritage home?
If your home is heritage listed or in a heritage conservation area, you may need council approval. The slate roof installation then has to follow heritage guidelines on materials, colour and the method of installation.
Can I stay in my home while a new slate roof is installed?
On our St Leonards and Manly slate roof projects, both homes stayed occupied for the whole installation. On the Manly home, we staged each part of the roof work to keep noise, dust and disruption down.
How long will a new slate roof last?
With proper maintenance, a slate roof can last well over 100 years. Slate itself is very durable, and it resists the salt air, wind and seasonal weather changes found on the Northern Beaches and Lower North Shore.
Book a Slate Roof Installation Inspection in Sydney
If your slate roof has slipping slates, leaks, failing valleys or timber you are worried about, the first step is an inspection. We will check the slate, timber, underlay, flashings and ridgeline, then explain whether your roof needs repairs, a restoration or a new slate roof installation. Contact Slate Roof Restorations to arrange an inspection of your Sydney home.
What Others Are Reading:
Our Services
Get A Free Quote
Get in touch today for a free, no-obligation quote on your roofing needs.
